Price: $12.90
(as of Nov 16,2024 07:21:32 UTC – Details)
The prices listed in the article are accurate as of the time of publication and may change. Please check the linked page for the most up-to-date prices.
View on Amazon
Here are Today’s Best Deals at Amazon
Product Description
Add to Cart
Add to Cart
Add to Cart
Customer Reviews
3.9 out of 5 stars
10
3.8 out of 5 stars
104
2.6 out of 5 stars
3
2.9 out of 5 stars
4
4.8 out of 5 stars
6
—
Price
—
— $35.00$35.00 $49.90$49.90
— $15.00$15.00
Compatible with
for Raspberry Pi 5 for Raspberry Pi 5 for Raspberry Pi 5 for Raspberry Pi 5 for Raspberry Pi 5, with POE function for Raspberry Pi 5
Mounting Position
TOP Bottom Bottom Bottom TOP TOP
M.2 Key-M NVMe SSD Supported
DUAL 2280 2230/2242/2260/2280 DUAL 2230/2242/2260/2280 QUAD 2230/2242/2260/2280 2230/2242/2260/2280 2230/2242/2260/2280
Matching Case
P579 P580 P580-V2 X1011-C1 P579, but DC jack is not available to use P579
Support NVMe SSD Boot
Yes (Requires EEPROM 2024/05/17 and later version) Yes Yes (Requires EEPROM 2024/05/17 and later version) Yes (Requires EEPROM 2024/05/17 and later version) Yes Yes
Support Hailo-8 AI Accelerator
Yes No Yes No Not tested Yes
Specifications
Model X1001 Compatible With for Raspberry Pi 5 PCIe Connector 1x 16-pin pitch 0.5mm SSD Connector 1x M.2 KEY-M 67P M.2 Key-M NVMe SSD Supported 2230/2242/2260/2280 PCB Size 87 mm x 56 mm Power Supply 5Vdc +/-5% power via FFC, converted to 3.3V max 3.5A to power the SSD Packing List 1 x X1001 V1.1 NVMe SSD Shield; 1 x PCIe FFC cable(30mm length); 3 x M2.5x17mm F/F Spacers; 6 x M2.5x5mm Screws; 1 x M2x4mm Screw
Troubleshooting Steps
Check the hardware connection, make sure the FFC cable is fully inserted with right direction. (Change FFC cable to test if you have one.)Update EEPROM firmware: Check and upgrade the bootloader firmware to the latest version;Refer to Geekworm X1001 WiKi to check the SSD incompatibility List, change SSD to test.Enable PCIe: Must make sure to enable PCIe in the OS on the NVME SSD you are booting, instead of the OS on SD card. Too many people just enable PCIe in the OS on the SD CARD.Set NVME boot order;DON’T enable PCIe 3.0, ONLY PCIe 2.0 is supported by Raspberry Pi fundation.If your SSD is old and has a DOS partition, delete the DOS partition and repartition the SSD (feedback from buyer)Refer to the guide on Geekworm Wiki for more specific operations!!!(wiki.geekworm.com/NVMe_SSD_boot_with_the_Raspberry_Pi_5)
Note: The Raspberry Pi 5, M.2 NVME SSD, power supply is not included in the packing list.
Overview
The X1001 V1.1 shield is an NVME M2 SSD PIP (PCIe Peripheral Board) for the Raspberry Pi 5 that uses the new PCIE interface of the Raspberry Pi 5 to utilise the NVME M2 SSD for fast data transfers and ultra-fast booting.
Features
Model: X1001Minimalist design, easy to install.FFC cable is only 30mm length.Compatible with other HAT shield;Supports installation of official Pi 5 active cooler;Supports 2230/2242/2260/2280 NVME M2 ssd.Can Power the X1001 shield directly from the FPC PCIe ribbon (providing maximum 5W of continuous power)Integrated with XH2.54 5V power connector, just use it if you are using a ultra large capacity SSD if the current is not enough.
PS:
Maximum current for PCIe wire is 1A, and voltage is 5V.If you find that the SSD is not working properly, it is possible that the power supply of SSD is not enough, then you need to check the current requirement of your SSD to decide whether power the SSD separately.The X1001 hardware has no limit on NVME SSD capacity, which is dependent on the Raspberry Pi OS.
How to Power
Can power the X1001 shield directly from the FFC PCIe ribbon (providing maximum 5W of continuous power)
Packing List
1 x X1001 V1.1 NVMe SSD Shield1 x PCIe FFC cable(30mm length)3 x M2.5x17mm F/F Spacers6 x M2.5x5mm Screws1 x M2x4mm Screws (to fix MVME M2 SSD)
Compatibility: Pi 5 PCIe M.2 HAT only compatible with Raspberry Pi 5 2GB/4GB/8GB SBC (NOT include Raspberry Pi 5), Model: X1001
M2 Key-M NVMe SSD Supported: Support M.2 KEY-M NVMe SSD 2230/2242/2260/2280 length installation; Comes with SSD copper pillar for 2230/2242/2260 SSD installation
User Manual and FAQ: Google Geekworm Wiki and search X1001 and its FAQ; Refer to the FAQ to do troubleshoot step by step if can’t boot/recognize from NVMe SSD
How to Power: Power the X1001 shield directly from the FFC PCIe ribbon; Use the PD 27W power adapter for Raspberry Pi 5
Packing List: 1 x X1001 PCIe Peripheral Board, 1x Accessories Pack; Note: not include Raspberry Pi 5, SSD, TF card or power adapter
Customers say
Customers like the functionality, ease of installation, and speed of the input output card. They mention it works perfectly, is simple to install, and boots quickly. Some appreciate the cooling capacity and design. However, some customers have different opinions on the fit and mount hardware.
AI-generated from the text of customer reviews